Recently, I talked about rip cuts giving the needed information for anyone who is about to start woodworking. If you are interested and want to learn how to do a rip-cut, you can take a look at my\u00a0rip-cut article<\/a>.<\/p>\n But now, let\u2019s focus on the crosscut.<\/p>\n Crosscut refers to cutting the wood perpendicular to the grain<\/strong>. The thing you need to understand is that the crosscut is usually a shorter cut.<\/p>\n It is basically cutting across the grain of the wood and it is a very tough type of cutting<\/em>.<\/p>\n What makes it so hard?<\/strong><\/p>\n When you cut across the grain, you need to cut lot more wood fibers<\/strong>, which requires more effort and it is way tougher for the saw.<\/p>\n To make it easier, you should use a blade that has small teeth, but many of them<\/strong>. In addition to this, the number of teeth is important as you need to remove the\u00a0sawdust\u00a0after the cutting.<\/p>\n Well, you may be able to do many tasks and avoid crosscutting, but if you are serious about woodworking, crosscut is something you need to learn to do as soon as possible<\/strong>.<\/p>\n If you have ever cut wood for furniture, or whatever you were planning to do, you know the importance of doing crosscut, as not every piece of wood can be cut with a rip-cut.<\/p>\n It is true that crosscut is a cut that requires some experience and serious control of your saw, but once you learn it, it will be much easier for you to finish any task.<\/p>\n First of all, let\u2019s differ things \u2013 for doing crosscuts you can use a miter\u00a0saw, table saw or a circular saw.\u00a0 Table saws can be expensive, but don\u2019t let that discourage you \u2013 you can make crosscuts with a circular saw that is much cheaper can do a good job.<\/p>\n In this article, I will only focus on the crosscutting with a circular saw. Without any hesitations, let\u2019s go.<\/p>\n You\u00a0won\u2019t need anything\u00a0more than your saw<\/em>, a measuring tape<\/em> as well as a pencil<\/em> to mark the length, square and clamps<\/em> to hold the square.<\/p>\n I didn\u2019t mention the safety glasses and other protective gear<\/em> as you always need to have them before taking the saw in your hands.<\/p>\n Next, make sure that the blade is extra sharp<\/strong>, and the right one for the type of the wood you are about to cut.<\/p>\n Once you do that, adjust the depth<\/strong> for not more than a quarter inch more than the depth of the wood.<\/p>\n Now, pay close attention to this step<\/strong>. Measure the distance from the outside of the blade and the desired length of the cut, and count back the distance you first measured (the blade distance). Use the square to line it with the mark.<\/em><\/p>\n You can draw a line with the pencil, or just the clamps to fix the square on the wood. Personally, I would recommend you the second option<\/em>.<\/p>\n Pull the trigger, and cut a straight line<\/strong> \u2013 if you have the square fixed on the wood, it would be way much easier to follow it.<\/p>\n Go to the end of the wood, and let the piece to follow freely. And, that is, you have done a crosscut.<\/p>\n It may seem harder than a rip cut, but it is not a big deal. If you want to check the comparison of both types of cuts, you can read more on my rip-cut versus a crosscut article<\/a>.<\/p>\n You may find that in certain situations when you make a lot of crosscuts you may want to make your self a crosscut jig for your circular saw. This can make repeated cuts quicker, easier and more accurate. Check out the video for how a crosscut jig works and how to make one.<\/p>\nWhat is a crosscut?<\/h2>\n
<\/p>\n
Can I cut wood without using crosscuts?<\/h2>\n
How to do a crosscut?<\/h2>\n
Crosscut jig<\/h2>\n